Volvo EC60E Скачать руководство пользователя страница 283

Страница: 283 / 342

NOTE!

Protect electrical leads in an appropriate way and

be careful not to damage the cab prefilter when

cleaning the machine.

NOTICE

Do not spray with high pressure into the sealing of

the slewing ring, the water may penetrate and affect

the characteristics of the grease.
- Use a soft sponge.

- Finish by rinsing the whole machine with only

water.

- Always lubricate the machine after washing.

- Touch-up the paint finish when required.

Paint finish maintenance

- Machines which are used in corrosive

environment suffer more from rust than others. As

a preventive measure it is recommended that the

paint finish should be maintained every sixth

months.

- At first clean the machine.

- Apply Dinol 77B (or corresponding transparent

waxy anti-rust agent) at a thickness of 70-80 µ.

- A protective layer of underseal Dinitrol 447 (or

corresponding) may be applied under the

mudguards where mechanical wear is expected.

Touch-up painting

- Check if there are any damaged areas of the paint

finish.

- At first clean the machine.

- Rectify any damage to paint finish in a

professional way.

282

Maintenance

Maintenance service, when required

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 283 / 342

Результаты поиска

Содержание EC60E

Отзывы: