Volvo EC60E Скачать руководство пользователя страница 85

Страница: 85 / 342

Warning

- The red central warning symbol is shown.

- The buzzer will sound until the required action

has been performed.

- The alarm text will be shown until the required

action has been performed.

- Repair or contact a workshop authorized by Volvo

for information.

V1139556

Machine immobilized

V1155511

- Geofence broken

The machine is
immobilized due to:

- Timefence broken
- System tampered
- Machine movement
- Battery power lost
- Remote immobilization
- No coverage

V1160926

Electronic system tampered

Contact service

Machine inoperable

Machine immobilized

- Geofence broken

- Timefence broken

- System tampered

- Machine movement

- Battery power lost

- Remote immobilization

- No coverage

Contact service

Electronic system tampered

Machine inoperable

V1155510

Anti-Theft system tampered

Machine immobilized

Contact service

V1160719

Electronic sys power lost

Contact service

Machine will be inoperable

Contact service

Anti-Theft system tampered

Machine immobilized

Contact service

Electronic sys power lost

Machine will be inoperable

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 85 / 342

Результаты поиска

Содержание EC60E

Отзывы: