Volvo EC60E Скачать руководство пользователя страница 203

Страница: 203 / 342

Mechanical attachment bracket

Bucket installation with mechanical

attachment bracket

WARNING

The attachment quick coupler may be open

regardless of what is indicated by the alarm signal

or on the instrument panel. Therefore, always check

that the attachment quick coupler is locked

securely. Also read the instructions in the operator's

manual.

NOTICE

Check that the attachment is locked securely by

pressing the front edge of the attachment against

the ground so that the machine's front end is raised

slightly.
1 Remove linch pin (4) and extract locking pin (3).

2 Rotate the locking pin 90° to lock it in extracted

position.

3 Lower the dipper arm into a position where the

attachment bracket connects with front bucket

pin (5).

4 Lower the attachment bracket towards rear

bucket pin (6). Tilt the bucket rearwards (bucket

in) until the hook on the attachment bracket is

properly connected to the rear bucket pin.

5 Check that the bucket is securely fastened by

simultaneously pressing the bucket to the

ground and forward.

6 Lower the bucket to the ground.

1 Front hook

2 Rotating hook

3 Locking pin

4 Linch pin

5 Front bucket pin

6 Rear bucket pin

202

Operating techniques

Mechanical attachment bracket

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 203 / 342

Результаты поиска

Содержание EC60E

Отзывы: