Volvo EC60E Скачать руководство пользователя страница 46

Страница: 46 / 342

Display unit

Start sequence

Initial start sequence is performed as follows.

A Volvo logo

If the operator turns the ignition switch to the

operating position, the Volvo logo on the I-ECU

screen lights up for a few seconds.

B Daily maintenance

The operator can see daily maintenance items

once a day. This screen is dismissed by pressing

the ESC button or SELECT button and

disappears automatically after 5 seconds if there

is no button input.

V1159067

DAILY MAINTENANCE

Engine oil level
Coolant level
Water separator
Air cleaner
Hydraulic oil level
Travel/working light

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 46 / 342

Результаты поиска

Содержание EC60E

Отзывы: