Volvo EC60E Скачать руководство пользователя страница 91

Страница: 91 / 342

10) ESC button
This button is used to go back to the previous

screen or to cancel without saving.

The ESC button is also used to turn off the warning

light and sound.
11) Select button
This button is used to confirm the item or setup that

the user selects.
12) Engine speed control switch
This control switch is used to change the engine

speed.

Increase the engine speed by turning the control

switch clockwise.

Reduce the engine speed by turning the control

switch counter-clockwise.

Power max. mode switch

Press down switch (A) to activate power

maximum mode.

If the machine is not operated in P-mode for more

than 5 seconds and the auto idle selector switch is

activated, the engine speed automatically goes

down to idle mode. When the machine is operated

again, it returns to P-mode again.
NOTE!

When turn off the engine, turn the engine speed

control switch to low idle mode.

V1159068

A Power max. mode switch

Instrument panels

Instrument panel, right

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 91 / 342

Результаты поиска

Содержание EC60E

Отзывы: