Volvo EC60E Скачать руководство пользователя страница 69

Страница: 69 / 342

Overload pressure: This is to preset of overload

pressure. See page

for more information

regarding overload warning button on keypad.

- Select the preferred pressure value using the

arrow buttons.

- Save the selected value using the SELECT

button. Use the ESC button to cancel without

saving.

Operating pattern: The machine control pattern

can easily be changed. For more information,

see page

100

Language

Supported languages are listed in the screen in

the form of their own languages.

Use the arrow buttons to scroll up and down to

find your specific language. Press the SELECT

button to select the chosen language. The

screen reverts to the former screen displaying

the newly selected language.

V1158349

Setup

Overload pressure

Set overload pressure:

V1158485

Setup

Operating pattern

ISO/SAE type

BHL type

V1137903

Setup

Language

English

Deutsch

Español

한국어

Language select

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 69 / 342

Результаты поиска

Содержание EC60E

Отзывы: