Volvo EC60E Скачать руководство пользователя страница 55

Страница: 55 / 342

Hydraulic oil : This shows the value for

remaining time to next hydraulic oil service.

- Change interval : This shows the value of

hydraulic oil interval in the unit hours.

- Reset time remaining : This shows the value

for remaining time to next hydraulic oil service.

When the "Reset time remaining" reaches 40

h, 20 h, and 0 h, the check screen with "Reset

time remaining" and "Interval" will pop up on

the I-ECU. Service the maintenance items

which should be serviced in that interval. For

the service interval and maintenance items,

see page

310

- Reset? : After servicing the maintenance

items, the time can be reset. Press ESC button

to "Cancel " or SELECT button to "Yes". When

the time is reset, "Reset time remaining" will

be displayed to “Change interval”.

Service

Hydraulic oil

xxxh

Hydraulic oil

Change interval

xxxh

Reset time remaining

Reset?

V1158207

Yes

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 55 / 342

Результаты поиска

Содержание EC60E

Отзывы: