Volvo EC60E Скачать руководство пользователя страница 20

Страница: 20 / 342

EU EMC Directive

The electronic equipment of the machine may in

some cases cause interference to other electronic

equipment, or suffer from external electromagnetic

interference, which may constitute safety risks.

The EU EMC directive about "Electromagnetic

compatibility", 2014/30/EC, provides a general

description of what demands can be made on the

machine out of a safety point of view, where

permitted limits have been determined and given

according to international standards.

A machine or device which meets the requirements

should be CE marked. Our machines have been

tested particularly for electromagnetic interference.

The CE marking of the machine and the declaration

of conformity also cover the EMC directive.

If other electronic equipment is fitted to this

machine, the equipment must be CE marked and

tested on the machine with regard to

electromagnetic interference.

Presentation

CE-marking, EMC-directive

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 20 / 342

Результаты поиска

Содержание EC60E

Отзывы: