Volvo EC60E Скачать руководство пользователя страница 86

Страница: 86 / 342

Control types for X1 and X3 operation

If a machine has a "proportional control option" for

X1 or X3, the user can set one of these 3 types.

Otherwise the user is only allowed to set one of 2

types that are "Push" or "Toggle". Refer to page

100

for more details on optional levers.

- Push

- Toggle

- Proportional
Control using on/off switch on the control lever

1 Toggle type in the I-ECU

Actuator for X1 is activated by pressing the

on/off switch on the control lever and it will stay

active even when the switch is released. The

actuator will be deactivated when the same

switch is pressed again or the other switch for

opposite direction is pressed.

2 Push type in the I-ECU

Actuator for X1 is activated while the on/off

switch is pressed (On position). The function will

be deactivated when the on/off switch is

released.

Control using proportional switch on the control

lever

1 Toggle and Push-button type in the I-ECU

These controls with proportional switch are

similar as the ones with on/off switch but it has

a special point to activate the actuator because

the proportional switch also has a proportional

value.

In toggle type, the actuator will be activated by

moving the proportional switch to one direction

and it will be deactivated when the switch is

moved to same direction again or to opposite

direction.

2 Proportional type in the I-ECU

Actuator for X1 or X3 is activated proportional to

the movement of the proportional switch.

V1158332

Push

Toggle
Proportional

Control type

V1158749

Control lever with on/off switch

V1158750

Control lever with proportional switch

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 86 / 342

Результаты поиска

Содержание EC60E

Отзывы: