Volvo EC60E Скачать руководство пользователя страница 62

Страница: 62 / 342

Delete

Use the arrow buttons to place the cursor

(highlighting bar) on the required item, and

then press the SELECT button.

1 Select "Delete" after entering "X1".

2 Select the tool to delete using the arrow

buttons and press the SELECT button.

NOTE!

Selected work tool can not be deleted.

Dozer blade

Raising speed : This is to preset raising speed

of dozer blade.

Lowering speed : This is to preset lowering

speed of dozer blade.

Response mode : The operator can adjust the

movement sensitivity of dozer blade when

operating the levers. “Active” mode is the most

sensitive.

V1158338

Setup

Select work tool
Adjust tool setting

New
Delete

Hammer

Shear

VOLVO

Delete setting

Raising speed

Dozer blade

Max

Min

V1158339

Lowering speed

Response mode

Active

Max

Min

Setup

Dozer blade

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 62 / 342

Результаты поиска

Содержание EC60E

Отзывы: