Volvo EC60E Скачать руководство пользователя страница 66

Страница: 66 / 342

5 Select “Select work tool” and then choose

the new tool which is newly created.

Wiper interval : Operator can adjust the wiper

interval of 1st step.

Auto idle time

The basic concept of “Auto idle” is to reduce fuel

consumption. The engine rpm will be lowered

automatically to idle mode, if the Auto idle

button is ON and any of control levers (pedals)

or engine speed control switch are not operated

for a certain time. See page

for more

information regarding Auto idle button on

keypad.

V1158346

Setup

Select work tool
Adjust tool setting

New

Hammer

Shear

VOLVO

Select work tool

V1158347

Setup

Wiper interval

Set wiper interval:

4 s

V1137900

Setup

Auto idle time

Set auto idle time:

5 s

Auto idle time

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 66 / 342

Результаты поиска

Содержание EC60E

Отзывы: