Volvo EC60E Скачать руководство пользователя страница 11

Страница: 11 / 342

Engine

The new engine which provide excellent

performance is equipped with a four-cylinder,

vertical, electronic controlled high pressure fuel

injectors, in-line turbo charger and water cooled

diesel engine type. This engine fully meets the

demands of the latest EU Stage IV / US Tier 4 final

emissions regulations.
NOTE!

Machines with engines for the US market may not

be sold or used within the EU, and machines with

engines for the EU market may not be sold or used

within the USA, unless the engine is replaced with

an engine valid for the applicable market. The

market for which the engine is intended is indicated

on the emission plate and by the engine's serial

number (see page

Presentation

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 11 / 342

Результаты поиска

Содержание EC60E

Отзывы: