Volvo EC60E Скачать руководство пользователя страница 271

Страница: 271 / 342

Maintenance service, every 500

hours

Radiator and coolers, cleaning

Cleaning interval depends on the environmental

condition the machine is operating. Therefore,

clean all fins when required or at least every 500

hours.
If the engine temperature becomes too high even

though the coolant level is correct, the radiator

should be cleaned.

WARNING

Risk of serious injury.

Compressed air, water jets or steam may cause

damage to unprotected skin and eyes.

Always wear personal protective gloves, goggles

and clothing when using compressed air, water jets

or steam.

NOTICE

DO NOT use steam to clean the condenser core.

The refrigerant can overheat! When cleaning with

water, protect the electrical components.
1 Position the machine on even, firm and level

ground.

2 Open the rear engine hood.

3 Clean any mud, dust or leaves attached to the

radiator fins and oil cooler fins with compressed

air or steam

4 Check the rubber hose for wear and cracks. If

damaged, replace it. Check the hose clamp for

looseness.

NOTICE

When using compressed air, keep the nozzle at a

distance from the fins to prevent damage. Damaged

fins may cause leakage or overheating.
If the engine temperature still remains high after

cleaning the cooler, contact a workshop authorized

by Volvo CE for remedial action.

V1155534

A Radiator and hydraulic oil cooler

270

Maintenance

Maintenance service, every 500 hours

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 271 / 342

Результаты поиска

Содержание EC60E

Отзывы: