Volvo EC60E Скачать руководство пользователя страница 116

Страница: 116 / 342

Operator comfort

Operator seat

The operator seat meets the requirements

according to EN ISO7096. The operator seat is

designed to provide maximum comfort and reduce

vibration to the operator during normal machine

operation.

WARNING

Risk of serious injury.

Uncontrolled touch of control levers could cause

unexpected movement of machine or parts. This

could result in serious injury.

Always lock the control lock out lever before

adjusting the seat.

NOTICE

Installation and maintenance of the operator seat

may only be carried out by authorised and

competent personnel.

NOTICE

To obtain maximum comfort and eliminate the risk

of accidents, you must make sure that all seat

adjustments have been carried out correctly before

starting the machine.
NOTE!

The seat is intended for use by one seated

occupant only.

Other controls

Operator comfort

115

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 116 / 342

Результаты поиска

Содержание EC60E

Отзывы: