Volvo EC60E Скачать руководство пользователя страница 238

Страница: 238 / 342

Entering, leaving and climbing

the machine

Entering, leaving and climbing the

machine

NOTE!

For safety, observe the following rules.

Do not jump on/off a machine, especially never

get on / off when the machine moves.

Never grasp the control lever to get on / off.

Use handholds and steps when entering, leaving

or climbing the machine.

Use the three-point grip, that is two hands and

one foot or two feet and one hand.

Always face the machine.

Always wipe mud and oil off all footboards,

handrails and your footwear, especially clean the

windows, rear view mirrors and lights.

Clean your boots and wipe your hands before

getting on the machine.

Do not use hand grip (A) of the cab door as a

support when entering, leaving and climbing the

machine. it is not strong enough to be used as a

support. it should only be used for closing the

door.

V1078575

Safety when servicing

Entering, leaving and climbing the machine

237

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 238 / 342

Результаты поиска

Содержание EC60E

Отзывы: