Volvo EC60E Скачать руководство пользователя страница 54

Страница: 54 / 342

Fuel filter : This shows the value for remaining

time for next fuel filter service.

- Change interval : This shows the value of fuel

filter interval with in the unit hours.

- Reset time remaining : This shows the value

for remaining time for next fuel filter service.

When the "Reset time remaining" reaches 40

h, 20 h, and 0 h, the check screen with "Time

remaining" and "Interval" will pop up on the I-

ECU. Service the maintenance items which

should be serviced in that interval. For the

service interval and maintenance items, see

page

310

- Reset? : After servicing the maintenance

items, the time can be reset. Press ESC button

to "Cancel " or SELECT button to "Yes". When

the time is reset, "Reset time remaining" will

be displayed to “Change interval”.

Service

Fuel filter

xxxh

Fuel filter

Change interval

xxxh

Reset time remaining

Reset?

V1158206

Yes

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 54 / 342

Результаты поиска

Содержание EC60E

Отзывы: