Volvo EC60E Скачать руководство пользователя страница 176

Страница: 176 / 342

Steer, brake, accelerate, shift gears, and move

the attachments smoothly. (wheel machine only)

Minimize vibrations for long work cycle or long

distance travelling.

- Use suspension systems if available.

- If no suspension system is available, reduce

speed to prevent bouncing.

- Transport machines when there are long

distances between worksites.

Back pain associated with whole-body vibrations

may be caused by other risk factors.
The following guidelines can be effective to

minimize risks of back pains:

- Adjust the seat and controls to achieve good

posture.

- Adjust the mirrors to minimize twisted posture.

- Provide breaks to reduce long periods of sitting.

- Avoid jumping down from the machine.

- Minimize repeated handling and lifting of loads.

- Maintain reasonable weight and physical

condition.

Operating techniques

Whole-body vibrations

175

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 176 / 342

Результаты поиска

Содержание EC60E

Отзывы: