Volvo EC60E Скачать руководство пользователя страница 167

Страница: 167 / 342

In the event of slipping into swampy ground or

towing heavy objects, proceed as follows:

1 Attach a wire rope to the machine to be retrieved

or towed as shown in the illustration.

Ensure that the towing linkage is properly

connected, adequate for the purposes.

NOTE!

Put wood blocks between the wire rope and the

machine to protect the machine and wire rope from

damage.
2 Towing speed for short distance is maximum 2

km/h.

Use other transportation for long distance.

NOTE!

Select the slow travel mode. Slowly drive the

machine when towing.
3 Keep the tow line angle as small as possible

Angle for pulling should not exceed 20° from the

horizontal line of tow lope and longitudinal axis

of the machine. Be careful there should not be

also interference with parts of the machine.

NOTE!

Keep the cable horizontal, straight, and parallel to

the tracks.
In case of towing light object:

Put a shackle in the tie-down hole (A) on the

undercarriage.

Do not use the hole (A) to another purpose.

Permissible force of the hole (A) : 3000 kgf (6613

lbf)

V1158745

166

Operating instructions

Retrieving and towing

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 167 / 342

Результаты поиска

Содержание EC60E

Отзывы: