Volvo EC60E Скачать руководство пользователя страница 24

Страница: 24 / 342

Communication equipment,

installation

NOTICE

All installation of optional electronic communication

equipment must be performed by trained

professionals and in accordance with the Volvo

Construction Equipment instructions.

Protection against electromagnetic

interference

This machine has been tested in accordance with

EU directive 2014/30/EC governing

electromagnetic interference. It is therefore very

important that all non-approved electronic

accessories, such as communication equipment,

should be tested before installation and use, since

they can cause interference to the electronic

systems of the machine.

Guidelines

The following guidelines must be followed during

installation:

The antenna placement must be chosen to give

good adaptation to the surroundings.

The antenna cable must be of the coaxial type.

Be careful to ensure that the cable is undamaged,

that the sheath and braid are not split at the ends,

the braid covers the connector ferrules and has

good galvanic contact with them.

The mating surface between the antenna

mounting bracket and the bodywork must have

clean metal surfaces, with all dirt and oxide

removed. Protect the mating surfaces against

corrosion after installation to maintain good

galvanic contact.

Remember to separate interfering and interfered

cables physically. Interfering cables consist of the

communication equipment's supply cables and

antenna cable. Interfered cables are those which

are connected to electronic devices in the

machine. Install the cables as close as possible

to earthed (grounded) sheet metal surfaces,

since the sheet metal has a shielding effect.

Presentation

Communication equipment, installation

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 24 / 342

Результаты поиска

Содержание EC60E

Отзывы: