Volvo EC60E Скачать руководство пользователя страница 143

Страница: 143 / 342

Safety rules when operating

Operator obligations

WARNING

Risk of fatal accidents.

Unauthorised persons within the work area around

the machine could lead to serious crushing injury.

• Clear all unauthorised personnel from the working

area.

• Keep a lookout in all directions.

• Do not touch control levers or switches during

start.

• Sound the horn before beginning operation.

The operator must operate the machine in such

a way that the risk of accidents is minimized for

both the operator and persons present on the

work site.

The operator must be thoroughly familiar with

how to operate and maintain the machine and

should undergo adequate training on the

machine.

The operator must follow the rules and

recommendations in the Operator's Manual, but

must also pay attention to any legislation and

national regulations or specific requirements or

risks that apply at the work site.

The operator must be thoroughly rested and must

never operate the machine when under the

influence of alcohol, medicine, or other drugs.

The operator is responsible for any load while

working with the machine.

- There must be no risk of the load falling off while

operating.

- Refuse to take a load which is an obvious safety

risk.

- Respect the stated maximum load for the

machine. Pay attention to the effect of different

distances to the centre of gravity and the effects

of different attachments.

142

Operating instructions

Safety rules when operating

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 143 / 342

Результаты поиска

Содержание EC60E

Отзывы: