Volvo EC60E Скачать руководство пользователя страница 166

Страница: 166 / 342

Retrieving and towing

WARNING

Risk of personal injury.

Faulty or improper lifting equipment could cause the

machine to break away from the lifting vehicle,

causing accidents, serious injury or death.

Use certified cables, lifting straps, slings, shackles

and hooks with adequate load capacity and never

lift the machine with a person in or on the machine.

WARNING

Risk of runaway machine.

Improper towing methods or faulty equipment could

cause the machine to break away from the towing

vehicle, causing accidents, serious injury or death.

Carefully follow the towing instructions and use only

certified towing equipment with adequate load

rating.
NOTE!

Only use the rear-mounted towing hook and the

attaching point for a towing bar for towing the

machine.

Operating instructions

Retrieving and towing

165

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 166 / 342

Результаты поиска

Содержание EC60E

Отзывы: