Volvo EC60E Скачать руководство пользователя страница 4

Страница: 4 / 342

Identification numbers

Make a note below of the identification numbers of the machine and its components.

Always use this information when contacting the manufacturer and when ordering spare

parts.

Manufacturer:

Volvo Group Korea Co., Ltd.

Seongsan-gu, Changwon-si, Gyeongsangnam-do,

Korea 51710

Machine PIN (Serial number)

Engine

Main pump

Swing motor

Track motor

Main control valve

• Please send any comments about the Operator's Manual to [email protected].

• Open source code used in this product can be got from the following web site. (http://

webdoc.volvo.co.kr/exc-oss)

Foreword

Identification numbers

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 4 / 342

Результаты поиска

Содержание EC60E

Отзывы: