Volvo EC60E Скачать руководство пользователя страница 151

Страница: 151 / 342

Starting with booster batteries

WARNING

Risk of explosion.

Batteries could explode due to the current surge if

a fully charged battery is connected to a completely

discharged or frozen battery.

Do not boost start a machine with a completely

discharged or frozen battery.
When starting with booster batteries, check that the

booster batteries or other power source have the

same voltage as the batteries of the machine. If the

batteries in another machine are used the engine of

that machine must be turned off.

NOTICE

Do not attempt to start the engine while the battery

charger is still connected to the mains. This may

cause serious damage to the electronic control

units.
1 Turn OFF the battery disconnect switch.

2 Remove the protections from the battery pole

studs.

Connect two 12 V batteries as follows :

3 Connect one of the jump leads between (+)

terminal on the battery of the machine and the

(+) terminal on the booster battery.

4 Connect the other jump lead between the (-)

terminal of the booster battery and a grounding

point on the machine.

NOTICE

Do not connect ground to the undercarriage on the

machine. This may seriously damage the swing

bearing.

150

Operating instructions

Starting engine

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 151 / 342

Результаты поиска

Содержание EC60E

Отзывы: