Volvo EC60E Скачать руководство пользователя страница 72

Страница: 72 / 342

- Set time format : The items "24h" and "12h"

decide how the I-ECU describes the time, 24-

hour-system or 12-hour-system.

- Set date format : The items "yy/mm/dd", "mm/

dd/yy", and "dd/mm/yy" decide how the I-ECU

shows the date. "yy" means year, "mm" means

month, and "dd" means day.

Display backlight

This is for changing the brightness of the I-ECU.

The adjusting bar in the screen is controlled

with the arrow buttons and the value is set with

the SELECT button.

Keypad backlight

The brightness of the keypad backlight is

changed by the adjustment. The adjusting bar

in the screen is controlled with the arrow

buttons and the value is set with the SELECT

button.

V1158489

Time/date
Set time format

Set time format

V1158490

Time/date
Set date format

yy/mm/dd

mm/dd/yy

dd/mm/yy

Set date format

V1158491

Setup

Display backlight

Brightness

Display backlight

V1158492

Setup

Keypad backlight

Brightness

Keypad backlight

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 72 / 342

Результаты поиска

Содержание EC60E

Отзывы: