Volvo EC60E Скачать руководство пользователя страница 141

Страница: 141 / 342

Rear-view mirrors
Using the rear-view mirrors, check that you have as

good visibility as possible towards the machine's

superstructure and lower frame, and with as wide

angle as possible. If not, adjust the rear-view

mirrors until good visibility is obtained, see figures.

V1177416

Machine’s top view

Rear-view camera (if installed)
Check the rear-view camera's display screen,

which is focused on the visible area, for good

visibility.
NOTE!

Camera is not adjustable on the machine.

V1177418

Machine’s top view

V1177414

Machine’s right view

V1177415

Machine’s left view

V1177417

Machine’s left view

140

Operating instructions

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 141 / 342

Результаты поиска

Содержание EC60E

Отзывы: