Volvo EC60E Скачать руководство пользователя страница 90

Страница: 90 / 342

3) Work lights control button
This button is used to control the work lights on the

boom, cab front and rear.

- Press the button short to turn on or off the work

lights. All settings remain if the system is turned

off.

- Press and hold in the button to set the work lights.

Use the arrow buttons to select the required work

light, and then press the SELECT button on the

keypad to turn on or off the work light.

When selecting “All”, all work lights are turned on

or off.

4) HVAC auto-mode select button
This button is used to control the HVAC system.

See page

118

5) Arrow up button
This button is used to scroll between items and

adjust each segment on the screen.
6) Defroster select button
This button is used to activate the defroster. See

page

118

7) Arrow left button
This button is used to move the cursor to the left.

Also press the button in order to decrease values.
8) Arrow down button
This button is used to scroll between items and

adjust each segment on the screen.
9) Arrow right button
This button is used to move the cursor to the right.

Also press the button in order to increase values.

V1158613

A Boom work lights

B Cab front light

C Cab rear light

Instrument panels

Instrument panel, right

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 90 / 342

Результаты поиска

Содержание EC60E

Отзывы: