Volvo EC60E Скачать руководство пользователя страница 111

Страница: 111 / 342

- Push the levers forwards or press down the front

end of the pedals = the machine is moving

forwards

NOTE!

When the sprockets are at the front side of the

machine, the machine will be moved to the opposite

direction as to above.

- Pull the levers rearwards or press down the heel

end of the pedals = the machine is moving

rearwards

NOTE!

When the sprockets are at the front side of the

machine, the machine will be moved to the opposite

direction as to above.
- Lever in the middle position (neutral) = the

machine stops

Left turn

When the sprockets are at the rear side of the

machine Push the right lever forward, the right

track rotates forward and the machine travels

forward as it turns to the left.

Pull the left lever backward, the left track rotates

in reverse and the machine travels backward as

it turns to the left.

Right turn

When the sprockets are at the rear side of the

machine

Push the left lever forward, the left track rotates

forward and the machine travels forward as it

turns to the right.

Pull the right lever backward, the right track

rotates in reverse and the machine travels

backward as it turns to the right.

V1158504

V1158609

V1158610

V1158611

110

Other controls

Controls

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 111 / 342

Результаты поиска

Содержание EC60E

Отзывы: