Volvo EC60E Скачать руководство пользователя страница 113

Страница: 113 / 342

Cab

Roll Over Protective Structure

The cab is designed to ensure minimum crash

protection space according to ROPS standard for

excavator.

Do not jump out of cabin if the machine should roll

over. Keep stay in seat wearing seat belt.

NOTICE

Check the clearance between bucket and cab or

spill guard by carefully moving the bucket as close

to the cab as possible. The risk of the bucket

knocking against the cab is greater if attachment

quick coupler is used or if the bucket is provided

with lifting eyes.

Protection from falling or scattering materials

(optional equipment)

Install the necessary protection guards according to

working conditions where falling or scattering

materials are capable of entering the operator's

cab.

Install front guards when working with a breaker.

In mining applications, FOPS must be adopted.

The above recommendations are based on

standard working conditions. Install necessary

additional protection guards in accordance with job

site conditions and local government regulations.

Contact authorized Volvo CE dealer to meet local

regulations.

Any damage can affect the strength of the structure.

Contact a qualified service technician for repairing

safety structure after damage.

For other work, install necessary guards as

appropriate where falling or scattering materials are

capable of entering the operator's cab.

Do not operate on travel with the front window open.

Ensure that non-essential personnel keep a safe

distance to both the machine and falling / scattering

material.

112

Other controls

Cab

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 113 / 342

Результаты поиска

Содержание EC60E

Отзывы: