Volvo EC60E Скачать руководство пользователя страница 278

Страница: 278 / 342

Filling with auto shut-off controller (optional

equipment)

Fuel filler pump is installed in the front cover on the

machine’s right side. Use it when filling the fuel in a

tank.
NOTE!

This pump is provided with an electronic overfilling

protection.
1 Open fuel filler cap (A) on the fuel tank.

2 Open the front cover on the machine’s right side.

3 Remove the strainer cover (F) which is installed

to protect the strainer from dust at the end of

hose (B).

4 Put the pump hose with strainer into the fuel

barrel.

5 Press the green start button (C). The pump will

run as long as the tank is not full.

- At any time during the refuelling or when the

drum has been emptied, the pump may be

stopped by pressing the red button (D).

- The pump will automatically stop when the fuel

level sensor is actuated. The pump cannot be

restarted until the fuel from the tank is used.

6 Fold the hose and reinstall the strainer cover.

7 Close the front cover.

8 Close the fuel filler cap on the fuel tank.

NOTICE

Never allow the fuel filling pump to run dry. The

pump may be damaged.

V1155537

A Fuel filler cap

B Fuel filler pump hose

C Start button (green)

D Stop button (red)

E Manual control button

F Strainer cover

Maintenance

Maintenance service, when required

277

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 278 / 342

Результаты поиска

Содержание EC60E

Отзывы: