Volvo EC60E Скачать руководство пользователя страница 200

Страница: 200 / 342

5 Make sure that the front lock device (B) is fully

opened before hooking it onto the bucket pin.

Otherwise, the bucket pin cannot be engaged

correctly.

NOTE!

If the front lock device (B) is not opened, follow the

below step by step.

1. Makes the bucket cylinder to its outer end

position (bucket in).

2. Increase the hydraulic pressure to the lock

cylinder carefully by moving the arm cylinder and

keeping it under pressure for about a second.
6 Curl out the attachment quick coupler and hook

it onto the bucket pin.

7 Slowly curl in the attachment quick coupler fully

towards the bucket.

8 Press the right attachment quick coupler switch

to position (0) to close the attachment quick

coupler. See page

for more information.

NOTE!

When the switch is in position (0), the buzzer

sounds and the check message for confirming and

indicator are displayed on theI-ECU.
9 Visually check that the front lock device is fully

engaged.

10 Lift and curl in the bucket fully towards the dipper

arm and hold it there for approximately 5

seconds to ensure that the attachment quick

coupler has locked securely to the bucket.

11 Press the left attachment quick coupler switch

for more than 0.7 seconds to confirm that the

attachment quick coupler is locked. Then the

buzzer sound will be turned off and the check

message and indicator will disappear. See page

for more information.

V1159891

Bucket in locked position

Front lock device

V1134968

Attachment quick coupler switch, right

V1147255

CONFIRM QUICK COUPLER

IS LOCK

Confirm quick coupler is locked

V1140835

Attachment quick coupler switch, left

Operating techniques

Attachments, connecting and disconnecting

199

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 200 / 342

Результаты поиска

Содержание EC60E

Отзывы: