Volvo EC60E Скачать руководство пользователя страница 129

Страница: 129 / 342

Area

This audio system is designed for operation in

different regions with different frequency ranges

and station technologies. The factory default of

the reception area is “EUROPE”. In addition, the

reception areas are “N-AMERICA”, “INTERNAL”

and “JAPAN” are available.

If you operate the audio system outside of

internal, you may first have to set a suitable

reception area in the menu:

1 Briefly press the MENU button to open the

user menu.

2 Press the > button until the TUNER menu item

is selected.

3 Press the Λ / V button until the “AREA” menu

item is selected.

4 Press the > button to set the reception area.

5 Press the > button to confirm the selected

area.

iPod mode

This audio system can play audio from iPod/

iPhone device via USB socket.

1 Insert the iPod via USB extension cable in

USB socket

2 Press the SRC button repeatedly until the USB

source is displayed.

A connected iPod is selected as audio source

as soon as the iPod has been recognized.

128

Other controls

Operator comfort

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 129 / 342

Результаты поиска

Содержание EC60E

Отзывы: