Volvo EC60E Скачать руководство пользователя страница 163

Страница: 163 / 342

Stopping

1 Select as level ground as possible to park the

machine.

2 Lower the attachment to the ground.

3 Leave the engine running at low idling speed for

approximately 2 minutes before shutting off the

engine.

NOTE!

Do not shut the engine down all of a sudden from

full load, but let it idle for a few minutes for

temperature equalization.
4 Turn the ignition switch to stop position.

5 Move the control lockout lever up to lock the

hydraulic system securely.

6 If the machine is to be left for any length of time,

the battery disconnect switch should be turned

off.

Keep in mind that the theft and burglary risk can be

minimised by:

- Removing the ignition switch when the machine

is left unattended.

- Locking doors and covers after working hours.

- Turning off the current with the battery disconnect

switch and removing the handle of the switch.

- Parking the machine where the risk of theft,

burglary and damage is minimised.

- Removing all valuables from the cab such as

cellular phone, computer, radio and bags.

- Chaining the machine.
By etching in the PIN-number or the national licence

plate number of the machine on its windows, it is

easier to identify stolen machines.

162

Operating instructions

Stopping

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 163 / 342

Результаты поиска

Содержание EC60E

Отзывы: