Volvo EC60E Скачать руководство пользователя страница 130

Страница: 130 / 342

Browse mode

In browse mode, you can directly search for and

select a certain track on the MP3/WMA data

carrier without interrupting the current play back.

In iPod mode, you can select and play a track

using the categories “Now Playing”, “All Tracks”,

“Playlist”, “Genre”, “Artist”, “Album”, “Composer”,

“Audiobook” and “Podcast”.

Selecting tracks in Browse mode

- During iPod playback, press the 1LIST button

to enter or exit the browse mode.

It will show current playing tracks stored in the

iPod, press button to view all category.

- Press the Λ / V button once or several times to

select a different folder.

- Press the > button to display the tracks of the

selected folder.

The first track of the folder is shown on the

display.
NOTE!

Press the < button returns you to the folder list.

- Press the Λ / V button once or several times to

select a different track.

- Press the > button to play the track.

The playback starts. You are existing the

browse mode.
NOTE!

Fast searching is not available in Browse mode.

Other controls

Operator comfort

129

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 130 / 342

Результаты поиска

Содержание EC60E

Отзывы: