Volvo EC60E Скачать руководство пользователя страница 248

Страница: 248 / 342

Maintenance

If the machine is to function satisfactorily and at

lowest possible cost, it requires careful

maintenance.

Regarding intervals for other maintenance, see the

"Service Programme" or the “Lubrication and

Service Chart” in this chapter.

Lubrication and service chart

The section "Lubrication and service chart"

describes the maintenance work which the operator

can carry out. If certain operations require trained

workshop personnel and special equipment, this

will be indicated.

Service history

After each completed service by a qualified service

technician, the service history should be filled in,

see page

334

. Service history is a valuable

document, which is referred to when selling the

machine.

Arrival Inspection

Before the machine leaves the factory, it is tested

and adjusted. The dealer or distributor must also

carry out arrival inspections according to the

applicable form.

Delivery Inspection

Before the machine leaves the factory, it is tested

and adjusted. The dealer or distributor must also

carry out delivery inspections according to the

applicable form.

Delivery Instructions

When handing the machine over, the dealer must

give the buyer "Delivery instructions" according to

V1068256

Maintenance

247

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 248 / 342

Результаты поиска

Содержание EC60E

Отзывы: