Volvo EC60E Скачать руководство пользователя страница 117

Страница: 117 / 342

Horizontal adjustment of seat and consoles

- Lift bar (1) up and push seat and consoles to

desired position.

- Let go of the bar and make sure the seat and

consoles are properly engaged.

Fore & aft adjustment, seat cushion

- Lift lever (2) and adjust the seat cushion fore &

aft.

Angle adjustment, seat cushion

- Lift lever (3) and adjust the angle of the seat

cushion. It may be necessary to reduce occupant

pressure on the seat cushion when performing

this adjustment.

Weight adjustment wheel

- By turning wheel (4) clockwise or counter-

clockwise a lighter or heavier weight of the

operator can be adjusted on scale (4). The value

displayed by the scale corresponds with the

different seat hardness settings.

Scale
Horizontal adjustment of seat

- Lift lever (6) and push the seat to desired position.

- Let go of the lever and make sure the seat is

properly engaged.

Backrest inclination adjustment

- Pull lever (7) up and put the backrest to desired

position.

- Let go of the lever and make sure the backrest is

properly engaged.

Seat heating switch (optional equipment)
This is used to warm up the operator seat.

The seat heating will activate when this switch is in

position (1) and the temperature is under 10 °C (50

°F). The seat heating stops when the temperature

is up to 20 °C ( 68 °F), and will activate again when

the temperature turns down under 10 °C (50 °F)

again by the first thermostat. If the first thermostat

malfunctions, the second thermostat cuts off the

seat heating at 25 °C (77 °F) and will activate again

when the temperature turns down under 14°C

(57.2°F).

NOTICE

To reduce the risk of fire the seat heating must be

switched off before you leave the seat.

V1129277

2 3 4 5 6

1 Horizontal adjustment of seat and

consoles

2 Fore & aft adjustment, seat cushion

3 Angle adjustment, seat cushion

4 Weight adjustment wheel

5 Scale

6 Horizontal adjustment of seat

7 Backrest inclination adjustment

8 Seat heating switch (optional

equipment)

V1065663

0 Seat heating, OFF

1 Seat heating, ON

116

Other controls

Operator comfort

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 117 / 342

Результаты поиска

Содержание EC60E

Отзывы: