Volvo EC60E Скачать руководство пользователя страница 287

Страница: 287 / 342

Engine air cleaner secondary filter,

replacing

Replace the secondary filter every 3rd time primary

filter is replaced or at least every 2 years.
If the indicator is still alight even though the primary

filter has been cleaned or replaced, the secondary

filter should be replaced.
The secondary filter (D) works as a protective filter

in case the primary filter (C) should be damaged.
NOTE!

The secondary filter must always be replaced,

never cleaned.
NOTE!

Never remove the secondary filter unless it is to be

replaced.
1 The secondary filter should be removed carefully

and with precision so that no impurities enter the

engine.

2 Carefully check that the new secondary filter is

correctly installed.

NOTICE

Take care of filters, oils and liquids in an

environmentally safe way.

Engine air cleaner cover, cleaning

The cover for aircleaner should be cleaned when

the primary filter is cleaned.

1 Remove the cover (B) and valve (A) from the air

cleaner.

2 Empty and clean the cover and valve.

3 Reinstall them on the air cleaner.

Radiator and coolers, cleaning

See page

270

V1066004

C Primary filter

D Secondary filter

V1066005

A Vacuator valve

B Cover

286

Maintenance

Maintenance service, when required

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 287 / 342

Результаты поиска

Содержание EC60E

Отзывы: