Volvo EC60E Скачать руководство пользователя страница 119

Страница: 119 / 342

Climate control system

HVAC system (Heating, Ventilation, Air

Conditioning)

The machine can be equipped with different kinds

of systems, for example, heater or heater with air

conditioning unit. Before operating the system,

check the detailed information for your machine.
1) HVAC control button

- Press the button briefly to turn on/off the HVAC

system. All settings remain if the system is turned

off.

- Press and hold in the button to setup the HVAC

system.

2) Arrow up button
This button is used to scroll between items and

adjust each segment on the screen.
3) Defroster select button
Press the button to activate the defroster. Fresh air

mode is selected automatically.
NOTE!

After 20 minutes, this setting is automatically

returned to the previous mode.
4) Arrow right button
This button is used to scroll between items and

adjust each segment on the screen.

Press this button in order to increase the

temperature.

V1137856

118

Other controls

Operator comfort

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 119 / 342

Результаты поиска

Содержание EC60E

Отзывы: