Volvo EC60E Скачать руководство пользователя страница 50

Страница: 50 / 342

Regeneration mode: This informs the operator

about which regeneration mode is selected at

the moment. It also allows the operator to select

a regeneration mode from 3 different modes.

The operator can select a regeneration mode

with the arrow buttons. When pressing the

SELECT button, the marked regeneration

mode is set. The screen reverts to the former

screen displaying the name of the newly

selected item.

- Automatic

- Parked (optional equipment)

- Dynamic (optional equipment)

Arctic regeneration (optional equipment) :

Arctic regeneration mode is used for machines

that operate in extreme cold climate areas

where the machines need to be left running

around the-clock without operator presence. To

use this optional mode, the parked

regeneration mode should be selected in

advance. When selecting "Enabled" in this

menu, the parked regeneration is started

automatically when needed without any further

operator action. This function will only be active

while in parked mode, regardless of

regeneration mode and will be "Disabled" by

default at startup or when leaving the parked

mode. This means that the regeneration

system can remain in an optimal mode, even

after longer periods of idling.

- Disabled

- Enabled

V1147261

Engine

Regeneration Mode

Automatic

Regeneration Mode

Automatic

Parked

Dynamic

V1147262

Engine

Arctic regeneration

Disabled

Arctic regeneration

Disabled
Enabled

Instrument panels

Display unit

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 50 / 342

Результаты поиска

Содержание EC60E

Отзывы: