Veichi AC90 страница 133 Скачать руководство пользователя | Manualshive

Страница: 133 / 193

background image

AC90 TENSION CONTROL FREQUENCY INVERTER MANUAL

Function Parameter specifications

128

increase quickly and even not stop increase while adding frequency, then should increase [FA.19] to improve
the protection respond speed.

FA.08

Energy braking act voltage

Setting range: 115.0-140.0%

Factory set: 120.0%

Energy braking act voltage:

Inverter energy braking begins while DC bus voltage rise up and over rated.Voltage

[FA.08]

setting. Voltage is DC20V lower than

[FA.08]

setting while energy braking stops. Please set it carefully.

It is only valid for inverter with inner braking parts. Inverters under AC90-T3-018T have build in braking parts.
AC90-S2-3R7T and inverters under than that with 220V input have built in braking parts. All inverters do not have
resistances. If need energy braking, please use optional resistance.

Note: If use energy braking, please close OV protection function. What mens set [FA.01] LED “0”digit and “00”
digit as 0. Energy braking only be valid in running, invalid while stop.

FA.09 Reserved

FA.10

Bus under-voltage
protection

Setting range:50.0-100.0%

Factory set:60.0%

It sets the lowest voltage limitation of DC side while inverter works normally. In location with lower grid, under-voltage
protection level can be reduced to keep inverter work normally.

Note: Too low grid voltage reduces inverter reliability.

FA.11

Speed fall act voltage at sudden
power down

Setting range: 0-200%

Factory set: 20%

FA.12

Main circuit aim voltage at
sudden power down

Setting range: 0-200%

Factory set: 90%

FA.13

Speed fall gain at sudden power
down

Setting range: 0.01-10.00

Factory set: 2.00

FA.14

Speed back waiting time at
sudden power down

Setting range: 0.1-100.0s

Factory set: 2.0s

Inverter reduces output frequency and compensates voltage by feedback energy while sudden power down.
While input voltage is lower than

[FA.11]

, inverter begins DEC. Bus voltage rise up back. While voltage back to

[FA.12]

,

it stop DEC. Inverter run at stable speed for

[FA.14]

time and ACC to frequency setting.

[FA.13]

is DEC time gain. Voltage rises up more quickly while it is bigger. It is suitable for small inertia load. Voltage

rises up more slowly while it is smaller. It is suitable for big inertia load.

FA.15

ACC OC protection point

Setting range: 100-250%

Factory set: 160%

FA.16

DEC OC protection point

Setting range: 100-250%

Factory set: 160%

FA.17

Current limit level while running

Setting range: 100-250%

Factory set: 160%

FA.18

Current limit frequency ACC/DEC
time while running

Setting range: 0.00-650.00s

Factory set: 10.00s

OC protection poing=inverter output current/inverter ratted current. 100% is rated current.

ACC OC protection point
DEC OC protection point
Current limit level while running

«
...
131
132
133
134
135
...
»

Содержание AC90


































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AC90

C1400-CO-VS-0S-I03

Бренд: NTI AG Страницы: 20

Continuous Rotation Servo

Бренд: Parallax Страницы: 9

Бренд: Teac Страницы: 1

Бренд: LaCie Страницы: 32

Бренд: ABB Страницы: 92

Бренд: ABB Страницы: 210

Бренд: ABB Страницы: 53

DVD+/-RW Slim External Drive

Бренд: Targus Страницы: 13

Бренд: Tecmar Technologies Страницы: 46

Бренд: Metronix Страницы: 171

Бренд: Micro Solutions Страницы: 29

Бренд: I/O Magic Страницы: 1

Бренд: Simu Страницы: 16

Powerpackage Q Series

Бренд: TOX PRESSOTECHNIK Страницы: 80

Бренд: YASKAWA Страницы: 106

Бренд: Ricoh Страницы: 6

Бренд: FEDERAL PACIFIC Страницы: 12

Бренд: Veichi Electric Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды