Veichi AC90 страница 132 Скачать руководство пользователя

Страница: 132 / 193

AC90 TENSION CONTROL FREQUENCY INVERTER MANUAL

Function Parameter specifications

127

current limited run. Inverter reduces current by reduce output frequency actively. Temperature be limited within70

℃

LED“00”digit: input phase lack protection selection
0: Invalid
1: Valid

Stop inverter output and alarm fault E.ILF while detect input phase lack.

LED“000”digit: output phase lack protection selection
0: Invalid
1: Valid

Stop inverter output and alarm fault E.oLF while detect output phase lack.

LED“0000”digit: reserved

FA.03

Protection function selection 4

Setting range: 0000-0011

Factory set: 0000

LED “0”digit: SC protection selection
0: Invalid
1: Valid.

Inverter judges E.SC alarm and removes distrubabce, only alarm for real fault signal. This function maybe

delay alarm time. Please ust it carefully.

LED“00”digit: OC protection selection
0: Invalid
1: Valid

Inverter judges OC alarm and remove distrubabce, only alarm for real fault signal. This function maybe delay

alarm time. Please ust it carefully.

LED“000”digit: reserved
LED“0000”digit: reserved

FA.04

Fan control

Setting range: 0-2

Factory set: 1

Select fan run mode.

0: Fan run after electrify

No matter temperature of module is high or not, fan runs while inverter power on.

1: Fan stop related to temperature

Work while running. While inverter stops, fan runs while module temperature is

over 50 degree and stops 30 seconds after module temperature is lower then standard. While inverter runs, fan runs.

2: Fan stop while machine stop, run related to temperature

While inverter runs, fan runs while module temperature

is over 50 degree and stops 30seconds after module temperature is lower then standard. While inverter is stops, fan
stops.

Note: This function can prolong fan life.

FA.05

DEC OV protection

Setting range:110-150%

Factory set:120%

FA.06

Running OV protection point

Setting range:100-150%

Factory set:115%

Inverter DC bus rated voltage=inverter input rated voltage

1.414

DEC OV protection:

Set OV protection point while DEC. Only valid while

[FA.01]

LED “0” digit is 1.

Running OV protection point:

Set OV protection point while ACC or running at constant speed. Only valid while

[FA.01]

LED “0” digit is 1.

FA.07

OV protection max

frequency add

Setting range: 0-50.00Hz

Factory set:2.00Hz

OV protection max frequency add:

Frequency inverter usually adds frequency to restrain the temperature rise while

bus voltage is higher than

[FA.06]

. It limits the frequency adding range.

Note: 1, Increase this value can better restrain, but if too big, the speed maybe shakeing. 2, If the bus voltage

Содержание AC90


































































































































































































Результаты поиска

Содержание AC90

Отзывы:

Похожие инструкции для AC90

Бренды по названию

Популярные бренды

Veichi AC90, Руководство пользователя

Результаты поиска

Содержание AC90

Отзывы:

Похожие инструкции для AC90

Бренды по названию

Популярные бренды