manualshive.com logo in svg

Symmetricom TSG-3800 Series, Руководство пользователя

Линейка продуктов Symmetricom TSG-3800 Series представляет собой профессиональные оборудование для синхронизации времени. Для удобства пользователей доступны бесплатные инструкции по эксплуатации на manualshive.com, где вы сможете легко скачать руководство по эксплуатации на русском языке.

Поделиться
Скачать
background image

Operating the TSG-3800

Viewing Alarm Conditions

94

 

TSG-3800 User’s Guide

12778474-002-2  Revision F – March 2004

The first line of the response gives the ACTUAL start and stop 

date and times

 used 

in the calculation. These may vary from the requested times depending on the 
actual data available in the module. The lines following give the TDEV in 
nanoseconds for the time intervals listed. The time intervals listed range from 0.05 
to 1000 seconds, with the highest determined by the observation time period 
covered by the command or the available data. TDEV calculations for time intervals 
up to one third of the observation period are provided. However, some standards 
indicate that an observation period of at least 12 intervals should be used for the 
highest accuracy.

Viewing Alarm Conditions

The TSG-3800 reports three types of alarms: Critical, Major and Minor. A Critical 
alarm signifies that the output reference is invalid, or the Output modules have no 
clock source. A Critical alarm activates the major alarm relays and turns on the 
indicator. A Major alarm signifies that the output signals are not synchronized to an 
input. A Minor alarm signifies a condition that is not fatal to synchronization, but 
could lead to more significant problems. Both Major and Minor alarms contain relay 
contacts for Local, Remote, and Audio alarms. When an alarm condition arises, the 
CPU module activates corresponding contacts (on the rear panel of the shelf).

An ALARM CUT-OFF switch is available for turning off the Audio alarms. This 
switch is on the front panel of the CPU module. The ALARM CLEAR command 
(

Resetting Alarms

, on page 105) turns off the Major, Minor and Audio alarm 

contacts.

Alarm messages are available through the EIA-232 port. The EIA-232 port accepts 
commands for changing some fault limits. See 

Alarm Command

, on page 341.

Events, Fault Thresholds, Faults, and Fault Modes

An event is an occurrence of a changed condition within the TSG-3800. This 

change in condition

 can be a lost signal (for instance LOS), or instrument related, 

for example, module failure. When the magnitude or number of errors surpass a 
specific threshold (default or operator settable), a fault condition exists.

A fault mode defines the action that the TSG-3800 takes with the occurrence of a 
fault. The operator can assign any of four fault modes to the individual input signal 
characteristics of any Input module: Frequency, MTIE, AIS, BPV, CRC, LOS, SSM 
and OOF. The operator can also define a threshold for causing a fault. For AIS, 
BPV, CRC, LOS, OOF, Frequency, and MTIE, a separate threshold for clearing the 
fault can be set. 

Table 3-4

 shows the relationship between fault modes and TSG-3800 action 

followed by a description of each mode.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание TSG-3800 Series



















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TSG-3800 Series

FJC 45135 User Manual preview
45135
Бренд: FJC Страницы: 2
Tascam US-1200 Quick Start Manual preview
US-1200
Бренд: Tascam Страницы: 8
B-K lighting Union Bollard Installation Instructions preview
Union Bollard
Бренд: B-K lighting Страницы: 5
B-K lighting RE1 Installation Instructions preview
RE1
Бренд: B-K lighting Страницы: 4
B-K lighting PS Installation Instructions preview
PS
Бренд: B-K lighting Страницы: 3
Kawai CS11 Setting Manual preview
CS11
Бренд: Kawai Страницы: 10
Federal Signal Corporation Electraray 225 Instruction Sheet preview
Electraray 225
Бренд: Federal Signal Corporation Страницы: 12
Pari eFlow rapid User Manual preview
eFlow rapid
Бренд: Pari Страницы: 11
Pari O-PEP System Instructions For Use preview
O-PEP System
Бренд: Pari Страницы: 2
Haas DT-1 Removal And Replacement Procedures preview
DT-1
Бренд: Haas Страницы: 5
Waters 2707 Quick Install Manual preview
2707
Бренд: Waters Страницы: 4
Waterpik ClearView Instructions For Use preview
ClearView
Бренд: Waterpik Страницы: 2
Landoll 3631-30 Operator'S Manual preview
3631-30
Бренд: Landoll Страницы: 144
Castellini SKEMA 6 CP Manual preview
SKEMA 6 CP
Бренд: Castellini Страницы: 299
Lowenstein Medical elisa 300 Instructions For Use Manual preview
elisa 300
Бренд: Lowenstein Medical Страницы: 457
LOFTNESS GrainLogix XLB10 Owner'S Manual And Parts Book preview
GrainLogix XLB10
Бренд: LOFTNESS Страницы: 104
Raytec RL F 25 Installation Manual preview
RL F 25
Бренд: Raytec Страницы: 8
Fillauer ALP Aluminum Product Manual preview
ALP Aluminum
Бренд: Fillauer Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды