42
Safety Practices
WEEE Instructions for PerkinElmer Products
A label with a crossed-out wheeled bin symbol and a rectangular bar indicates that
the product is covered by the Waste Electrical and Electronic Equipment (WEEE)
Directive and is not to be disposed of as unsorted municipal waste. Any products
marked with this symbol must be collected separately, according to the regulatory
guidelines in your area.
The objectives of this program are to preserve, protect and improve the quality of
the environment, protect human health, and utilize natural resources prudently and
rationally. Specific treatment of WEEE is indispensable in order to avoid the
dispersion of pollutants into the recycled material or waste stream. Such treatment
is the most effective means of protecting the customer's environment.
Requirements for waste collection reuse, recycling, and recovery programs vary by
regulatory authority at your location. Contact your local responsible body (e.g.,
your laboratory manager) or authorized representative for information regarding
applicable disposal regulations. Contact PerkinElmer at the web site listed below
for information specific to PerkinElmer products.
Dispose of waste in accordance with the regulations applicable to
your locality, state, and/or country.
Avertissement: Eliminer les déchets en conformité avec les
règlements applicables à votre localité, état, et / ou pays.
!
Warning
Содержание AVIO 500
