Omron NT - SUPPORT TOOL FOR WINDOWS V4 Скачать руководство пользователя страница 501 | Manualshive

Страница: 501 / 573

background image

Appendix C

NT Transfer Utility

494

If you want to change the folder, select the desired folder from the Existing
Folders or directly input the folder name. (If a folder that does not exist in the
hard disk is specified, the specified folder is automatically made.)

After specifying the folder, click on

.

Installation of the specified programs is implemented; files are copied.
During program installation, the progress of the processing is indicated as a
percentage.

(9) After the completion of installation, the folder specified in step (8) is dis-

played along with the installation completion message.

Click on

, then click on

in the setup completion screen.

Installation operation is completed.

Uninstall

An uninstaller (uninstall software) is supplied with the NT Transfer Utility.
If you want to remove the NT Transfer Utility from your personal computer, run
the uninstaller to delete the NT Transfer Utility program files and installation in-
formation. (Note that the data saved by the NT Transfer Utility is not deleted.)

Starting the uninstaller from the Windows start menu

Select “Uninstall Transfer Utility” in the same folder where the short-cut to the
Support Tool is stored.

Example:Assuming the short-cut to the Support Tool exists in the Start\Pro-

gram\Omron\NTST4.8E\Uninstall Transfer Utility folder
Select the uninstaller by the following operation.
[Start]

→

[Program]

→

[Omron]

→

[NTST4.8E]

→

[Uninstall Transfer

Utility]

After the start up of the uninstaller, follow the instructions displayed on the
screen.

«
...
499
500
501
502
503
...
»

Содержание NT - SUPPORT TOOL FOR WINDOWS V4






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NT - SUPPORT TOOL FOR WINDOWS V4

Бренд: Acer Страницы: 4

850DP - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 2

COLDFUSION MX 61-CFML

Бренд: MACROMEDIA Страницы: 34

AV Tutor MCFBV1-D

Бренд: Califone Страницы: 1

NETWORK AND SECURITY MANAGER 2010.4 - REV1

Бренд: Juniper Страницы: 244

PRIVILEGED USER MANAGER 2.2

Бренд: Novell Страницы: 37

Бренд: MACROMEDIA Страницы: 232

DVD MOVIEFACTORY 5

Бренд: Ulead Страницы: 72

Бренд: da Vinci Technologies Страницы: 249

Vigil Server V5.00

Бренд: 3xLogic Страницы: 134

ANTI-VIRUS 5.0 - FOR SAMBA SERVERS

Бренд: KAPERSKY Страницы: 64

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 267

Бренд: TC Electronic Страницы: 10

Бренд: TC Electronic Страницы: 7

Бренд: Harman Kardon Страницы: 19

Бренд: Canon Страницы: 92

G3 Station HX-DU010EC

Бренд: Samsung Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды