Omron NT - SUPPORT TOOL FOR WINDOWS V4 Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 573

background image

7-8

Section

F-Key Input Notify Table

305

[Enter]

Ignored

---

---

[TAB]

[TAB]

[Enter]

NG

---

---

[TAB]

[Enter]

Ignored

---

---

[TAB]

100.03

[TAB]

comment3

[Enter]r

OK

0010003

comment3

[TAB]

100.04

[TAB]

[Enter]

OK

0010004

[TAB]

100.05

[Enter]

NG

---

---

[TAB]

[TAB]

comment4

[Enter]

NG

---

---

[TAB]

[TAB]

[TAB]

[EOF]

NG

---

---

[TAB]

100.06

[TAB]

comment5

[EOF]

OK

0010006

comment5

ABC

[TAB]

100.07

[TAB]

comment6

[EOF]

OK

0010007

comment6

: Blank space

[TAB]: TAB code

[Enter]: Enter code

[EOF]: End of file

Reference:

It may take time to import I/O comments when there are many I/O comments.

There are the PLC address, I/O Comment, and Reference in an I/O comments
table. Addresses with no comment and no reference will not be downloaded to
PT. (See below)

Referenced

Not Referenced

With Comments

Without Comments

×

: Can be downloaded

×

: Cannot be downloaded

Lines in an I/O comment table with only the PLC address input (for future use
etc.) will not be downloaded to PT, and as a result, when the data is uploaded to
the Support Tool, the line itself will be lost. (This also applies when saving data
in mmi format.)

Support Tool cannot import more than 3,000 PLC addresses with comments.
Therefore, if there are more than 3,000 PLC addresses with comments, only
the addresses will be imported for PLC addresses from entry 3001 onwards.
(I/O comment import operation will be finished normally.)
Rejected entries are displayed in the Error Log. Check them by selecting [Error
Log] from the [View] menu and print them.

7-8

F-Key Input Notify Table

This table is only available for NT11S/NT11. The F-Key Input Notify Table con-
sists of four entries. Each entry is assigned to a function key in the PT device. It
specifies a PC (PLC) memory bit to be related to a corresponding function key.

7-8-1 Operation Procedure

An F-Key Input Notify Table is displayed by following the operation described be-
low.

Select [Tools] (menu bar)

→

[Table]

→

[F-Key Input Notify] tab

→

Specify the

edit field

→

«
...
316
317
318
319
320
...
»

Содержание NT - SUPPORT TOOL FOR WINDOWS V4






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NT - SUPPORT TOOL FOR WINDOWS V4

Бренд: TAA Страницы: 28

DEEP FREEZE - INTEGRATING WITH ALTIRIS...

Бренд: FARONICS Страницы: 22

Web SmartDeviceMonitor Standard

Бренд: Ricoh Страницы: 1

dc5750 - Microtower PC

Бренд: Promise Technology Страницы: 114

Streaming Client

Бренд: BARIX Страницы: 51

Traffix Transcend Traffix Manager

Бренд: 3Com Страницы: 186

Бренд: E-Mu Страницы: 42

15606-011408-9330 - MAPGUIDE R6.3 SITE LIC-UPG R6

Бренд: Autodesk Страницы: 94

Application Server 10.1.3.4

Бренд: Oracle Страницы: 170

SSD ULTRA320 SCSI 3.5" DC-000255

Бренд: SanDisk Страницы: 3

Бренд: Garmin Страницы: 4

Бренд: Panasonic Страницы: 78

MOTOwi4 - RFS7000 - Network Management Device

Бренд: Motorola Страницы: 2

CDMA CONNECTIVITY KIT

Бренд: Motorola Страницы: 18

SCX 4500W - Personal Wireless Laser Multi-Function...

Бренд: Samsung Страницы: 30

Бренд: Microsoft Страницы: 74

Бренд: Microsoft Страницы: 122

76H-00326 - Office Ultimate 2007

Бренд: Microsoft Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды