huawei(config-if-vdsl-0/4)#
alarm-config 1 1
huawei(config-if-vdsl-0/4)#
quit
3.
Run the
display traffic table ip
command to query the traffic profiles that exist in the
system.
huawei(config)#
display traffic table ip from-index 0
{ <cr>|to-index<K> }:
Command:
display traffic table ip from-index 0
---------------------------------------------------------------------------
TID CIR CBS PIR PBS Pri Copy-policy Pri-Policy
(kbps) (bytes) (kbps) (bytes)
---------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-pri
1 2496 81872 4992 163744 6 - tag-pri
2 512 18384 1024 36768 0 - tag-pri
3 576 20432 1152 40864 2 - tag-pri
4 64 4048 128 8096 4 - tag-pri
5 2048 67536 4096 135072 0 - tag-pri
6 off off off off 0 - tag-pri
---------------------------------------------------------------------------
Total Num : 7
According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.
NOTE
l
If no traffic profile in the system meets the service requirement, run the
traffic table ip
command to
configure a new traffic profile.
l
On the MA5600T/MA5603T/MA5608T, the user access rate can be limited by either a traffic profile
or a VDSL line profile. When both profiles are configured, the user bandwidth adopts the minimum
value in the two profiles. In this example, the traffic profile is used to limit the user access rate.
4.
Run the
service-port
command to create a service port. The index of the new service virtual
port is 3, the access port is port 0/4/1, traffic profile 5 meets the service requirement, and
the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.
huawei(config)#
service-port 3 vlan 50 vdsl mode atm 0/4/1 vpi 1 vci 39 inbound
traffic-table index 5 outbound
traffic-table index 5
huawei(config)#
service-port desc 3 description MA5600T/MA5603T/MA5608THW/
Vlanid:50/vdsl/smart
5.
Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.
huawei(config)#
mac-address max-mac-count service-port 3 16
Step 6
Configure the PPPoA-PPPoE protocol conversion.
This step is to configure the PPPoA MAC address pool. The start MAC address in the MAC
address pool is 0000-1111-1010, and the maximum number of the MAC addresses in the MAC
address pool is 300. The PPPoA-PPPoE protocol conversion is enabled and the service
encapsulation mode is LLC.
huawei(config)#
mac-pool xpoa 0000-1111-1010 300
huawei(config)#
pppoa enable
huawei(config)#
encapsulation 0/2/0 vpi 1 vci 39 type pppoa llc
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
3 Configuring the DSLAM Services
Issue 01 (2014-04-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
271
