manualshive.com logo in svg

Baumuller b maXX BM2500, Руководство по эксплуатации

Операционный мануал для Baumuller b maXX BM2500 можно скачать бесплатно с нашего сайта. Этот руководство поможет вам ознакомиться с функциональностью и правильным использованием продукта. Нажмите на manualshive.com, чтобы загрузить свой экземпляр руководства по эксплуатации.

Поделиться
Скачать
background image

Description of the Software Modules and Parameters

Parameter manual 

b maXX

 

BM3000

Document no.: 5.12001.07 

679

of 820

4

This requirement applies only if the segment is not skipped before the branching (in this 
case 0) was made. This means that the polynomial for the 0 segment must be calculated 
at least once for each cycle even at a peak master axis speed. 

Effects when reloading curves 

Supposed the original curve corresponds to the black curve in 

Z

Fig. 219

–

. The user re-

loads a curve during the process, which is in accordance with the course of the red curve. 

In contrast to the interlinking change mentioned above here the drive paths and segment 
coefficients from 0 to 8 are changed. The interlinking data (successor, predecessor) re-
main identical and no other segment numbers are added to the interlinked curve. 

Therefore, the segment 8 is accordant to the red curve in 

Z

Fig. 219

– 

on page 678 after 

it was reloaded and combined. The newly combined curve consists of 7 segments, 
whereby the segments 1 to 6 were changed due to reloading.

The activating point of the curve is decisive. If the curve is activated in segment 0 then 
the segments 5 to 7 and 0 to 3 of the original curves are in the interim buffering. Such as 
presented by the interlinking change the active segment 0 is processed, then goes to seg-
ment 1 and during this change the three successors of the segment 1 in the interim buff-
ering are updated. Segment 1 is processed with the previous data before segment 2 of 
the combined curve is activated. As the segments smoothly join next to each other the 
segment 2 of the combined curved is added to the segment 1 of the original curve. An 
offset occurs and therefore the required curve position is not achieved.

If the switching to the combined curve occurs in segment 7, the segments 4 to 7 and 0 to 
2 are loaded in the intermediate buffer. Segment 0 follows segment 7. After segment 0 
the segment 1 of the combined curve is loaded in the intermediate buffer and is pro-
cessed. In this case the required processing of the curve is achieved.

While reloading the curves the curve segment in which the combined curve is switched 
and the following segment in both curves shall be identical in the original as well as in the 
combined curve.

4.8.13.9 Real master axis

By the bit 12 of the 

Z

122.2

–

 mode the real master axis can be activated. 

Therefore, the device must provide two encoder inputs!

The master axis position of the following axis is coupled to the actual position of the mas-
ter axis encoder at the second encoder input of the device. The parameter 

Z

122.3

–

 mas-

ter axis position revolutions and 

Z

122.4

–

 master axis position angle are carried along in 

this mode by the actual value of the master axis encoder. 

Options at the real master axis:

m

Inverting the master axis position by bit 14 of the 

Z

122.2

–

 mode. 

m

Smoothing of the master axis position and compensation of the resulting delay by 
bit 17 of the 

Z

122.2

–

 mode, details see 

Z

122.26

–

. 

The following applies especially in regard to double axis units: 

m

Here the master encoder of the following axis is the motor encoder of the master axis. 

Содержание b maXX BM2500























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для b maXX BM2500

Kawai ES100 Technical Speci? Cations preview
ES100
Бренд: Kawai Страницы: 5
Jata hogar 80 Instructions Manual preview
80
Бренд: Jata hogar Страницы: 12
Macherey-Nagel NANOCOLOR Advance Operating Instruction preview
NANOCOLOR Advance
Бренд: Macherey-Nagel Страницы: 45
NARDA nbm-520 Operating Manual preview
nbm-520
Бренд: NARDA Страницы: 64
QUBINO Smart meter Manual preview
Smart meter
Бренд: QUBINO Страницы: 2
S+S Regeltechnik HYGRASREG KH-30 Operating Instructions Manual preview
HYGRASREG KH-30
Бренд: S+S Regeltechnik Страницы: 16
CONDTROL Vector 30 User Manual preview
Vector 30
Бренд: CONDTROL Страницы: 8
CA.MI T-PLUS User Manual preview
T-PLUS
Бренд: CA.MI Страницы: 68
Velleman DVR8T3 Quick Installation Manual preview
DVR8T3
Бренд: Velleman Страницы: 107
Nidec-Shimpo FGE-0.5XY Operation Manual preview
FGE-0.5XY
Бренд: Nidec-Shimpo Страницы: 6
Reed Instruments R3525 Instruction Manual preview
R3525
Бренд: Reed Instruments Страницы: 14
horiba TW-100 Instruction Manual preview
TW-100
Бренд: horiba Страницы: 175
Oakton WD-35606-00, WD-35606-05 Operating Instructions Manual preview
WD-35606-00, WD-35606-05
Бренд: Oakton Страницы: 10
Fuji Electric ZRE-2 Instruction Manual preview
ZRE-2
Бренд: Fuji Electric Страницы: 85
Dakota Digital VHX systems Installation And Operation Manual preview
VHX systems
Бренд: Dakota Digital Страницы: 34
Value WT26 Series Manual preview
WT26 Series
Бренд: Value Страницы: 20
Oceanic DATATRANS Owner'S Manual preview
DATATRANS
Бренд: Oceanic Страницы: 114
Fluke 80i-2010s Instructions Manual preview
80i-2010s
Бренд: Fluke Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды