manualshive.com logo in svg

Baumuller b maXX BM2500, Руководство по эксплуатации

Операционный мануал для Baumuller b maXX BM2500 можно скачать бесплатно с нашего сайта. Этот руководство поможет вам ознакомиться с функциональностью и правильным использованием продукта. Нажмите на manualshive.com, чтобы загрузить свой экземпляр руководства по эксплуатации.

Поделиться
Скачать
background image

Operating Modes

Parameter manual 

b maXX

 

BM3000

Document no.: 5.12001.07

Baumüller Nürnberg GmbH

558

of 820

4.8

absolute. A relative target specification is signed, however the same parameter, 

Z

118.9

–

 Positioning Target Position, is used.

m

CANopen mode with range offset: 

In this special mode, the distinction between absolute or relative target specification is 
also made via Bit 6 of the control word, but for absolute specifications a range offset is 
included in the calculation of the target position. In this mode the numerical range for 
positioning should be regarded as signed. The target specification is carried out using 
parameter 

Z

118.16

–

 Positioning Relative Target Position.

m

CANopen mode without range offset:

In this case there is no range offset calculated in the target position for absolute target 
specification. Otherwise, this mode is identically with the CANopen mode with range 
offset. 

m

Absolute positioning to angle in positive and negative direction respectively or shortest 
way:

In this case only the angle of the target position is used and this angle will be ap-
proached in the next possible position.

m

Positioning to absolute angle with selectable number of revolutions

In this case it will be positioned to the denoted angle. Thereby the number of revolu-
tions is calculated relatively.

m

Absolute modulo positioning with direction select or shortest way 

This type of positioning can be applied at axes on which an endless moving (rotational 
axis application) is desired and the target position should be preset in modulo format. 
The translation of a between connected transfer element (e.g. gear) is taken into ac-
count via the definition of the range of modulo values (

Z

118.20

–

 Modulo value). 

4.8.2.10 Change of Operating Mode to Positioning

When changing to the Positioning mode, a changeover with speed matching is possible. 
To do this, the drive maintains the previous speed for 16 ms (starting from the mode 
changeover). Within this time a new positioning task can be started and will then be ac-
cepted directly. After the 16 ms have elapsed, the drive is braked to Speed 0 with the pre-
set hold deceleration (Parameter 

Z

121.8

–

 Hold Deceleration).

The speed matching is activated via Parameter 

Z

118.2

–

 Positioning Mode, Bit 0.

4.8.2.11 Halting a Running Positioning Task

A running positioning task can be halted by setting the Halt bit (Control Word 

Z

108.1

–

, 

Bit 8). The data from the current positioning set are used for the deceleration ramp. The 
execution of the Halt command is indicated immediately in Positioning Status 

Z

118.1

–

, 

Bit 9. When the set speed = 0 (Positioning Status 

Z

118.1

–

, Bit 4) and the Speed Zero 

message (

Z

6.2

–

) is present at the same time, the axis is considered to be halted and Set 

Value Reached (Status Word 

Z

108.3

–

, Bit 10) is set.

When the Halt bit is reset, the remaining travel is automatically completed and the status 
bits Set Value Reached (Status Word 

Z

108.3

–

, Bit 10) and Positioning Status 

Z

118.1

–

, 

Bit 9 are cleared.

The interrupted positioning task can be resumed at the earliest when Set Speed = 0 is 
set. If the Halt bit is already set when a start command is set, the positioning task will not 
be started. It will only be started when the Halt bit is cleared.

Содержание b maXX BM2500























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для b maXX BM2500

Panasonic PV-V4524S Service Manual preview
PV-V4524S
Бренд: Panasonic Страницы: 72
Panasonic KW9M Eco-Power Meter Installation Instructions preview
KW9M Eco-Power Meter
Бренд: Panasonic Страницы: 2
Accurate Logic Pulse Series Operation Manual preview
Pulse Series
Бренд: Accurate Logic Страницы: 50
AccuEnergy Acuvim-L Series Owner'S Manual preview
Acuvim-L Series
Бренд: AccuEnergy Страницы: 188
VAMP 260 Operation And Configuration Instructions preview
260
Бренд: VAMP Страницы: 78
Bartec VOLUTANK Petro 3003 Quick Manual preview
VOLUTANK Petro 3003
Бренд: Bartec Страницы: 10
DODODUCK Q63 Instruction Manual preview
Q63
Бренд: DODODUCK Страницы: 2
Spasciani M 900 ABEK 15 Instructions For Use Manual preview
M 900 ABEK 15
Бренд: Spasciani Страницы: 26
Kipp & Zonen PAR lite Instruction Manual preview
PAR lite
Бренд: Kipp & Zonen Страницы: 32
BYK micro-TRI-gloss ? Operating Instructions Manual preview
micro-TRI-gloss ?
Бренд: BYK Страницы: 174
GAGEMAKER BXG-1000 Operation Manual preview
BXG-1000
Бренд: GAGEMAKER Страницы: 36
Varian UNITY INOVA NMR Hardware Installation preview
UNITY INOVA NMR
Бренд: Varian Страницы: 65
Jaquet HO 100 Operating Instructions Manual preview
HO 100
Бренд: Jaquet Страницы: 16
PHYWE 13621.00 Operating Instructions Manual preview
13621.00
Бренд: PHYWE Страницы: 6
Bender PEM353 Quick Start Manual preview
PEM353
Бренд: Bender Страницы: 4
TEKELEK TEK 603 Installation Manual preview
TEK 603
Бренд: TEKELEK Страницы: 3
Fresh Roast Systems ColorTrack Genesis User Reference Manual preview
ColorTrack Genesis
Бренд: Fresh Roast Systems Страницы: 9
In-situ TROLL 101 Operator'S Manual preview
TROLL 101
Бренд: In-situ Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды