manualshive.com logo in svg

Baumuller b maXX BM2500, Руководство по эксплуатации

Поделиться
Скачать
Baumuller b maXX BM2500 Скачать руководство пользователя страница 456

Controllers

Parameter manual 

b maXX

 

BM3000

Document no.: 5.12001.07

Baumüller Nürnberg GmbH

456

of 820

4.7

The position error is the difference between the position set value and the actual position.

The display of the parameter e1 Position deviation can be smoothed with a PT

1

 filter. The 

time constant of the filter is set in 

Z

18.18

–

. This filtering doesn't influence the position 

control! At the position controller input the unfiltered position deviation is evaluated. 

18.14

Kv position controller

Proportional gain of the position controller, units s-1.

The position controller is implemented as a P-controller.

It follows from this that with a Kv = 0 the position controller makes no contribution to the 
speed set value, as any control deviation (e1 position controller error) is multiplied by the 
Kv factor.

18.15

w2-Feedforward factor

Weighting factor for the speed feedforward at position control.

The speed feedforward is implemented as DT1 element. All changes to the position set 
value are differentiated with respect to time, multiplied by the parameter w2-Feedforward 
factor and smoothed subsequently with the 

Z

18.70

–

 w2-feedforward time constant. From 

this it follows that at speed feedforward of 0 the speed feedforward makes no contribution 
to the 

Z

18.21

–

 speed set value.

With speed feedforward of 1 (=100%) and constant change per unit time of the position 
set value, the speed feedforward provides exactly the required speed set value. In this 
case the position controller provides only the correction set value for tracking the angle.

18.16

18.17

w2 speed feedforward 

The parameter shows the actual output value of the speed feedforward, i.e. the value af-
ter the w2-Feedforward factor 

Z

18.15

–

 and the w2-Feedforward time constant 

Z

18.70

–

.

18.18

Time constant position error display filter

Time constant for the PT

1

 filter to smooth the position deviation display in parameter 

Z

18.13

–

 e1 position controller error. The filtering doesn't influence the position control!

Содержание b maXX BM2500























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды