Avaya J100 Series Скачать руководство пользователя страница 70

Страница: 70 / 528

Parameter name

Default value

Description

VLANSEP

Specifies whether the VLAN
separation is enabled or disabled
by the built-in Ethernet switch.

Value operation:

• 0: Disabled

• 1: Enabled

VLANSEPMODE

Specifies whether the VLAN
separation is enabled or disabled.

Value operation:

• 0: Disabled

• 1: Enabled

VLANSEPMODE is configured
through the settings file.

PHY2TAGS

Determines whether or not VLAN
tags are stripped on Ethernet
frames going out of the Computer
(PC) port.

Value operation:

• 0: Strip tags. VLAN tags are

stripped from Ethernet frames
leaving the computer (PC) port
of the phone.

• 1: Does not strip tags. VLAN

tags are not stripped from
Ethernet frames leaving the
Computer (PC) port of the
phone.

PHY2TAGS is configured through
the settings file.

Table continues…

Servers, VLAN, and IP configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 70 / 528

Результаты поиска

Содержание J100 Series

Отзывы: