Avaya J100 Series Скачать руководство пользователя страница 357

Страница: 357 / 528

Parameter name

Default value

Description

ENABLE_MODIFY_CONTACTS

Specifies if the list of
contacts and the function
of the contacts application
can be modified on the
phone.

Value operation:

• 0: No

• 1: Yes

ENABLE_MULTIPLE_CONTACT_WARNING

Specifies if a warning
message must be
displayed if there are
multiple phones registered
on a user's behalf.

Value operation:

• 0: No

• 1: Yes

Note:

Multiple registered
phones can lead to
service disruption.

ENABLE_OOD_MSG_TLS_ONLY

Specifies if an Out-Of-
Dialog (OOD) REFER
must be received over
TLS transport to be
accepted.

Value operation:

• 0: No, TLS is not

required.

• 1: Yes, TLS is required.

Note:

A value of 0 is only
intended for testing
purposes.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

357

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 357 / 528

Результаты поиска

Содержание J100 Series

Отзывы: